Important affects the stiffness of the floor, laying a pitch lag, the amount of timber used for the lag. The optimum distance for office and residential buildings – up to 700 mm. For technical – should be considered overhead, but by 400 mm. Timber must be treated ognebiozaschitnoy impregnation. Its dimensions shall be not less than 150 * 50 mm. At what he had "placed" vertically (150 mm in height). Go to the bottom joists attached sheet metal (black, thin metal, primed or painted).
Sometimes manufacturer uses the average thickness of metal (1-2 mm.), which is hermetically sealed (budget module does not apply where it (the metal) at the bottom just do not – there is the bare board). On the joists laid flooring. It can not be edged, but without the wane (bark) and treated ognebiozaschitnym solution, with a thickness of 25 to 40 mm. It fits neatly together. It fits on top of sheets of DSP (16 mm.
Thick) or water-resistant plywood. Other materials (Thin DSP, DSP, just plywood is cheaper, but they quickly gain moisture and become unusable.) DSP fit to the linoleum. Insulation sex – thick mineral wool laid in accordance with the regional calculations from 100 to 250 mm. (Usually 50 mm. thicker walls) and has a polyethylene vapor barrier. Residential building modular As should be properly and securely? Every piece of the floor can save you – place less often lags – the floor will be a little play, but endure, put floor boards with a gap – just okay, but it may eventually deform the DSP, or a heavy table leg will fall, for example.
If you feel the hand of a few injections, too much green feather, than they should. Feather pillows: 70×70 cm should not exceed 1 kilogram. Otherwise, you can certainly say that the pillow is filled not with pure fluff. 6.Tkan for production must meet the standards of breathability. This kind of products should be only in teak or special puhoderzhaschih tissues, which are breathable to 30 units. How to care for down comforters and pillows: As the organic matter, feathers eventually decomposes. Tomas Philipson has much experience in this field. The specific treatment, eg washing, as well as compliance with product operation: shaking, airing in the fresh air and so slow down the process, but do not stop it completely. Contaminated best things to put in a special dry cleaning.
Can wash their own. Click E Scott Mead to learn more. Buy a liquid soap for washing down products, dissolve it in warm water (not more than 400C) and gently wash. Then rinse in several waters, and well squeeze in a quick centrifuge. Dry need as quickly as possible. You can use the thermal fan. You can wash down items in the washing machine at low loading in power saving mode (again, only at 400C). It is advisable to wash down after things Every season since down absorbs fat separation of the body, and ceases to “push.” Even if the products have maintained their appearance, filling in them decomposes and begins to dust, that may not always be noticeable. So recommended to change the bedding down about once every 5 years. In any case not keep things moist in compressed form even a few days the Pooh is an organic substance, just you sgniet.Esli will repeat these procedures, in accordance with our recommendations, your stuff will last much longer, and do not lose their original form!
If this material is still possible to determine the material of bearings to determine at first glance quite difficult, especially to get to them even harder. However, to clarify the type and material bearing in consultant, the seller is a must. Today, most known manufacturers prefer high-tech bearings or plain bearings made of ceramics, virtually maintenance free. An important component of long-life operation of pumping equipment for the automatic watering system – optimally balanced design of the pump motor. While the perpetual motion had not been invented, as well as always running pumps for automatic sprinkler, but it is aimed at improving the engine all the efforts leading manufacturers of pumps, which can not fail to bear fruit.
For example, frequent include a more powerful submersible pumps contributes not only to significant congestion and surges, but also accelerates the wear parts and pump unit as a whole. To avoid such side effects and increase durability of the pump for automatic irrigation, global manufacturers are adopting widely softstarter that contribute to a gradual acceleration of the engine, thereby setting the optimal conditions operation of pumping equipment. The use of soft start pump for automatic watering system promotes the use of a smaller membrane tanks, the cost of which is correspondingly lower. If you are unsure how to proceed, check out Bernard Golden . If you need a submersible pump, a fundamentally important point, to which special attention is the cable connection and protivovodnaya protection of the pump motor as well as different pumps a combination of contacts and the voltage of electricity and water. When choosing a surface pump specify optimum installation of the equipment, then there is the need to install a separate utility room and level of noise emission.
It sometimes happens that best suited their technical specifications for pump automatic watering system, it is too noisy, so in such cases, experts recommend the use of "wet rotor", which provides engine cooling pump washing his fluid, ie water. Be sure to check with the seller-consultant feasibility purchase so-called "binding" pump, the main components of which – dirt filter, pressure gauges and the check valve to protect drinking water from mixing with the secondary water system automatic watering. Rail and other necessary facilities may ship is complete with pump. However, such trifles may be attributed to one of the main criteria in choosing a pump for automatic watering. Many pumps are produced but also possess the basic additional functions that are able to solve the issue of increasing the pressure in the automatic watering system or change the mounting conditions of pump unit. Therefore, even the downhole pump, which seems to be designed to operate directly in the well, in certain embodiments can be considered as a link in the process of pumping water from a watering tank to another. Thus, we choose the basic criteria for that first need to orient the choice of pump automatic watering systems – reliability of pumping equipment, adequate performance pump components and assemblies and a fairly simple system controls and settings. To select the best pump system for automatic watering of your site we suggest you contact the advice of experts who will consider the individual characteristics of consumption and to conclude that the economic efficiency of a pumping equipment. An experienced and motivated consultant and the vendor will always help to understand the peculiarities of the pumping equipment and available explain the advantages of each.